Speaker boxes are used widely and are a great way when installing component speakers and subwoofers in an enclosure. Since many subwoofers and speakers are sold separately from the speaker box, many people find it easier to make their own boxes than buying one. The speaker box might be challenging to build but is a great enhancement to the car stereo.
Materials
Power drill, ¾” bit, Sand paper, Spray glue, Silicone, Solder, Solder gun, Carpet, Screws, Razor blade, Router, Down spiral bit and Jigsaw
Making the speaker box
- The first step is deciding the speaker box size depending on the speaker size before making the measurements. The box needs to be slightly bigger compared to the sound driver.
- Step two is determining the wood type that is needed. A fiberboard of medium density or particle board allows for exemplary sound vibration. Six pieces of this wood should be obtained of the same size or a large piece can be bought and divided into six smaller pieces.
- Cut a circle the size of the speaker driver first on one board using the jigsaw. Screw the speaker driver by using the holes that are located at the side of the speaker.
- Drill holes to the board where the screws are supposed to be inserted and use a screw driver when attaching the box together.
- Before attaching the sides, drill a small hole at the board designated to be at the back for wire extension from the speaker to outside the box.
- Then attach the two sides, the top and the bottom but leave the back open first. This is done by first gluing the parts together before inserting screws into the already drilled areas.
- The back is left open so as to glue the carpet all around on the inside of the box. This enhances the sound quality from the box.
- Before attaching the back part of this sound monitor, make sure it is also lined with glued carpet on the inside.
- Add tiny braces or wedges to the speaker inside to help the sound be a bit steady and not vibrate a lot inside.
- Once closed, the carpet can further be used to cover the outside of the speaker but after all the edges have been sealed using fiberglass for insulation.
The speaker box is now complete and can be connected to the car stereo or if one prefers, at home.
Speaker boxes are used widely and are a great way when installing component speakers and subwoofers in an enclosure. Since many subwoofers and speakers are sold separately from the speaker box, many people find it easier to make their own boxes than buying one. The speaker box might be challenging to build but is a great enhancement to the car stereo.
Materials
Power drill, ¾” bit, Sand paper, Spray glue, Silicone, Solder, Solder gun, Carpet, Screws, Razor blade, Router, Down spiral bit and Jigsaw
Making the speaker box
- The first step is deciding the speaker box size depending on the speaker size before making the measurements. The box needs to be slightly bigger compared to the sound driver.
- Step two is determining the wood type that is needed. A fiberboard of medium density or particle board allows for exemplary sound vibration. Six pieces of this wood should be obtained of the same size or a large piece can be bought and divided into six smaller pieces.
- Cut a circle the size of the speaker driver first on one board using the jigsaw. Screw the speaker driver by using the holes that are located at the side of the speaker.
- Drill holes to the board where the screws are supposed to be inserted and use a screw driver when attaching the box together.
- Before attaching the sides, drill a small hole at the board designated to be at the back for wire extension from the speaker to outside the box.
- Then attach the two sides, the top and the bottom but leave the back open first. This is done by first gluing the parts together before inserting screws into the already drilled areas.
- The back is left open so as to glue the carpet all around on the inside of the box. This enhances the sound quality from the box.
- Before attaching the back part of this sound monitor, make sure it is also lined with glued carpet on the inside.
- Add tiny braces or wedges to the speaker inside to help the sound be a bit steady and not vibrate a lot inside.
- Once closed, the carpet can further be used to cover the outside of the speaker but after all the edges have been sealed using fiberglass for insulation.
The speaker box is now complete and can be connected to the car stereo or if one prefers, at home.
